R Vision Closures’ two caps, Aqua Cap and Bev Cap, are 28/15 mm aluminium ROPP closures made for five neck finishes: MCA I/II/III, MCA 7.5 R and MCA 7.5 RF on glass bottles, and PET and BPF on PET bottles. A ROPP cap has no thread of its own until it is capped, so the neck finish on the bottle is what the cap is formed against, and it has to be one the cap is made for. This page explains each of the five, which bottles use it, and how to read the finish off a bottle drawing before you order.
Why the finish decides the cap
An aluminium ROPP cap arrives at the filler as a plain shell. The capping head presses it onto the neck, a thread roller forms the aluminium into the bottle’s own thread, and a pilfer roller tucks the tamper ring under the bead below it. The neck acts as the mould. So two bottles that both measure 28 mm can still need different caps if their thread profile, height or bead position differ, and the finish named on the bottle drawing is the reference both the bottle maker and the cap maker work to.
| What the finish fixes | Why it matters for the cap |
|---|---|
| Thread diameter and profile | The shape the thread roller forms the shell into |
| Height from the rim to the bead | Where the skirt ends and the ring tucks under |
| Bead, or locking ring | What holds the tamper ring down on first opening |
| Sealing surface on the rim | Where the liner presses to make the seal |
| Pressure the finish is drawn for | Whether the neck holds a carbonated or vacuum fill |
The five finishes at a glance
| Finish | Bottle | Published by | What it is drawn for | Aqua Cap and Bev Cap |
|---|---|---|---|---|
| MCA I/II/III | Glass | The 28 mm MCA range, now in EN 17829:2023 | 28 mm screw finishes for glass beverage bottles; MCA III for bottles with internal pressure | Made for it |
| MCA 7.5 R | Glass | Formerly EN 16290, now in EN 17829:2023 | 28 mm screw finish for pressure capsules on returnable and one-way glass | Made for it |
| MCA 7.5 RF | Glass | Formerly EN 16289, now in EN 17829:2023 | 28 mm screw finish for pressurised or vacuum liquids | Made for it |
| PET | PET | The bottle or preform maker’s drawing | A 28 mm PET neck drawn to take a roll-on aluminium cap | Made for it |
| BPF | PET | The preform maker’s drawing | A 28 mm PET neck finish that preform makers list for soda and mineral water bottles | Made for it |
The glass finishes: MCA I/II/III, MCA 7.5 R and MCA 7.5 RF
The MCA finishes are the European family of 28 mm screw finishes for glass bottles closed with aluminium roll-on caps. Their dimensions were published as separate European standards and data sheets and were brought together in 2023 into one standard, EN 17829:2023, 28 millimetre screw finishes (MCA range), which replaced the earlier parts.
MCA I, II and III. The base 28 mm MCA finishes. They share the 28 mm diameter, and the bottle drawing names which one a bottle carries. MCA III is the finish for one-way or returnable glass with internal pressure, which is why it turns up on soft drink and sparkling water bottles. Glass makers list MCA II on lightly carbonated wines. If a drawing just says “MCA”, ask the glassworks which one.
MCA 7.5 R. A 28 mm finish written for pressure capsules on glass, first published in two parts, one for returnable glass and one for one-way glass. Returnable glass is washed and refilled many times, so its sealing surface has to keep its shape through repeated trips; 7.5 R is drawn with that in mind.
MCA 7.5 RF. The 28 mm finish for glass containers holding pressurised or vacuum liquids: carbonated drinks press outward on the closure, and a hot-filled drink pulls a vacuum as it cools.
The CETIE data sheet numbers for each MCA finish, and the other glass finishes a ROPP cap meets, are mapped in glass bottle neck finishes for ROPP caps. The Indian roll-on pilferproof finishes in IS 7511 (Part 4) are covered in neck finish standards on Indian glass bottles. Running these caps on glass, for water, soft drinks and juices, is the subject of the 28 mm glass bottle caps page.
The PET finishes: PET and BPF
Aqua Cap and Bev Cap are also made for two PET finishes, listed separately on both product pages.
PET. A 28 mm PET neck drawn to take a roll-on aluminium cap rather than a moulded plastic one. The neck carries the thread and bead the rollers work against, in PET instead of glass. The bottle or preform maker’s drawing names the finish; if it gives a plastic-closure code instead, check it against the cap before ordering.
BPF. A 28 mm PET neck finish. Preform makers still list 28 mm BPF preforms for soda and mineral water bottles, and closure makers list caps for it alongside the PCO finishes. Like any PET finish, it is identified by name on the preform drawing.
Most Indian PET water bottles carry finishes drawn for moulded plastic screw caps, such as the 28 mm Alaska neck and the PCO finishes, and those take a plastic cap, not a roll-on one. The survey of those finishes is in neck formats on Indian packaged water bottles. What changes when an aluminium ROPP cap runs on a 28 mm PET bottle is the subject of the 28 mm PET bottle caps page.
How to find the finish on a bottle drawing
The finish is the first thing to confirm before ordering, and the bottle drawing is where it is written.
- Look at the neck detail. A bottle or preform drawing carries an enlarged view of the neck with the finish named beside it or in the title block, for example “Finish: MCA III” or “28 BPF”. That name is what the cap is matched to.
- Check the glassworks or preform catalogue. Bottle and preform makers list the finish against each item, often in the item’s name, such as “28 mm BPF preform”.
- No drawing? Measure, then ask. With a caliper, read the diameter across the thread and the depth from the rim to the underside of the bead, as set out in how to measure a bottle cap size. On the Indian roll-on standard, IS 7511 (Part 4), a 28 mm finish reads 26.77 to 27.41 mm across the thread with a depth of 15.17 to 15.67 mm. A reading in that range says the neck is a 28 mm roll-on finish; it does not say which one, so ask the bottle maker for the finish name.
- Send a sample. A sample bottle sent with the enquiry removes any doubt a drawing leaves.
| Drawing shows | What it means for Aqua Cap and Bev Cap |
|---|---|
| MCA I, MCA II, MCA III, MCA 7.5 R or MCA 7.5 RF | A glass finish the caps are made for |
| PET (roll-on) or BPF | A PET finish the caps are made for |
| PCO 1810, PCO 1881, Alaska, 29/25, 30/25, 26/22 | A PET finish for a moulded plastic cap; not a roll-on finish |
| 28-400, 28-410 and similar | A threaded finish for a plastic screw cap; see neck finish codes and cap sizes |
| A 30 mm, 31.5 mm or deep finish | A different ROPP size; see the ROPP cap size chart |
Whether a threaded plastic-closure finish can ever take a ROPP cap is answered in GPI and SPI neck finishes vs a ROPP finish.
The caps made for these finishes
| Aqua Cap | Bev Cap | |
|---|---|---|
| Size | 28/15 mm | 28/15 mm |
| Finishes | MCA I/II/III, MCA 7.5 R, MCA 7.5 RF, PET, BPF | MCA I/II/III, MCA 7.5 R, MCA 7.5 RF, PET, BPF |
| Ring | Three-part break-system PE ring | Retained PE ring: Round Ring, Two Slit or Five Slit |
| Liner | TPE | TPE, PVC-free |
| Pressure | Up to 8 bar | Up to 8 bar |
| Fills | Hot fill, cold fill, carbonated | Hot fill, cold fill, carbonated |
| Minimum order | 50,000 plain silver, 200,000 plain colours, 300,000 litho printed | Same |
| Lead time | 4 to 6 weeks | 4 to 6 weeks |
Both run on standard roll-on application machinery. Every line of both is on the ROPP cap specification sheet.
Frequently asked questions
Which neck finishes do Aqua Cap and Bev Cap fit?
Five: MCA I/II/III, MCA 7.5 R and MCA 7.5 RF on glass bottles, and PET and BPF on PET bottles. Both caps are 28/15 mm and are made for all five.
What is an MCA neck finish?
MCA is a family of 28 mm screw finishes for glass bottles closed with aluminium roll-on caps. The family includes MCA I, II and III and the 7.5 R and 7.5 RF finishes, and its dimensions are now published together in the European standard EN 17829:2023.
What is the difference between MCA 7.5 R and MCA 7.5 RF?
MCA 7.5 R is a 28 mm finish for pressure capsules on returnable and one-way glass. MCA 7.5 RF is the 28 mm finish for glass containers holding pressurised or vacuum liquids, such as carbonated or hot-filled drinks.
Can an aluminium ROPP cap go on a PCO 1881 or Alaska neck?
Not as a rule. PCO and Alaska are PET finishes drawn for moulded plastic screw caps. A ROPP cap needs a neck drawn for a roll-on closure, such as the PET and BPF finishes Aqua Cap and Bev Cap are made for. Check the finish named on the drawing.
How do I find the neck finish of my bottle?
Read it off the neck detail or title block of the bottle or preform drawing, or the maker’s catalogue. Without a drawing, measure the diameter across the thread and the depth to the bead with a caliper, then ask the bottle maker which finish it is, or send a sample bottle with your enquiry.
What is the ROPP 28 standard neck size?
On the Indian roll-on pilferproof standard, IS 7511 (Part 4), a 28 mm finish measures 26.77 to 27.41 mm across the thread with a depth of 15.17 to 15.67 mm to the underside of the bead. It takes a 28 mm ROPP cap, written as diameter by height, such as 28/15 mm.
Sources
- BSI, BS EN 17829:2023, Glass packaging, 28 millimetre screw finishes (MCA range), dimensions, which superseded EN 16289 (MCA 7.5 RF) and EN 16290 (MCA 7.5 R).
- CETIE, Finish data sheets (GME), for the MCA glass finish sheets.
- Bureau of Indian Standards, IS 7511 (Part 4): 1986, Roll-on Threads Pilferproof, for the 28 mm thread diameter and depth bands.
R Vision Closures makes Aqua Cap and Bev Cap at MIDC Malegaon, Sinnar, Nashik. To confirm a finish, send the bottle drawing or a sample through contact us.